Your Guide in Buying BLDC Circulation DC Water Pumps
Jarred Zhang
CEO at BLDC PUMP - Professional electric water pumps manufacturer for Aquarium and Circulation
DC powered pumps consume power directly from electric motor, battery, or solar panel to transmit liquid in different ways. Motorized pumps usually operate on 6V, 12V, 24V, or even 32V. On the other hand, DC solar-powered pumps use PV panels with solar cells that yield direct current when exposed to sunlight.
This article will further discuss the uses and specifications you have to check in buying BLDC circulation water pumps, plus a bonus list of our topnotch selling products that fully deserve your attention.
1. Uses and Specifications to Look for in Buying Water Pump
Our DC water pumps can be used for pumping different liquids, such as water, oil, acid, and alkali solution.
Whenever you needed to buy a pump, there are primary specifications that you need to consider when contemplating DC powered pump performance, like the pump head, flow rate, pressure, horsepower, and operating temperature.
(1) Head
The pump head is the height above the suction inlet that a pump can lift a liquid. Generally, if the fluid was pumped straight up, then the pump head is equal to the height it reaches.
(2) Flow Rate
The flow rate, or also called as capacity, is the volume of fluid that transmits through the pump in a given period. Hence, it defines the rate at which the pump can push liquid through the system.
(3) Pressure
The pressure is measured by how much resistance it can handle or overcome. So when selecting pumps, the discharge pressure of the pump must be equivalent or more than the required pressure for the system to achieve the desired flow rate.
(4) Temperature
Continuous use of water pumps and operating at full load may cause DC water motor pump temperature to rise. The reason why you should also be aware of the working temperature capacity of the pump you’re going to choose to avoid damage and unnecessary spending in the future.
2. Our Top of the Line BLDC Circulation DC Water Pumps
Here is a list of our best-selling DC water pumps.
(1) Circulation DC Water Pump DC30 Series
There’s only one model for this series. Check out our first-generation product:
Our DC30A model only weighs about 70g and has an inlet and outlet diameter of 8mm. Its max static head is 3m, which can achieve 240L/hour with an accessible limit of 60°C working temperature. This pump may have a small figure, but it is sturdy and high-efficient.
(2) Circulation DC Water Pump DC40 Series
Our DC40 series is generally applied for the most massive scale in circulating systems due to its durability and stability. These types have lower power and lower performance rate, not to mention the deficient noise level for about 25 decibels. See our different models for this series and their differences.
Our DC40A series weighs 220g with an inlet and outlet diameter of 14mm. Its max static head ranges from 4.5m, 5m, to 6m, which can achieve up to 840L/hour flow rate with an accessible limit of 60°C working temperature. Guaranteed that this type is submersible and 100% waterproof.
Our DC40C series has about 20mm inlet and outlet diameter, weighing 220g in total. Its max static head ranges from 4m to 6m, which can achieve up to 900L/hour flow rate. This type is maintenance-free, has a brushless DC motor, and can last to 30,000 working hours.
Our DC40D series has a thin inlet and outlet diameter of 10mm and weighs about 220g. Its max static head is available at 5m and 8m, achieving a range of 450 L/hour to a maximum of 550 L/hour flow rate. Our DC water pump series is magnetic driven, high-efficient, and waterproof.
Our DC40F series has a half-inch inlet and outlet diameter that weighs about 220g. You may choose from 4m, 5m, and 6m as static head measurements, which can achieve up to 960 L/hour flow rate—guaranteed that our series is submersible, 100% waterproof, safe to use, and highly efficient.
Our DC40H model has an 11m inlet diameter and an 8mm outlet diameter, weighing 220g. Its max static head ranges from 6.5m, 9m, and 11m, which can achieve up to 450L/hour flow rate. With a limit of 60°C working temperature, it can be used to pump water, oil, and alkali solution.
Our DC40M series has an operating voltage of 8V to 14V, which can only consume 4.8 watts. Its max static head is about 2.5m that can achieve up to 410 L/hour. Also, it has a 13mm inlet diameter and an 11 outlet diameter. This compact-sized water pump has a bedroom level quiet design since it only registers 25 decibels.
(3) Circulation DC Water Pump DC50 Series
The DC50 series has an excellent comprehensive performance. Here are some of the DC50 models that you should check out:
Our DC50A series weighs about 600g with an inlet and outlet 27mm diameter. Its max static head varies from 3.5m to 5m, which can achieve up to 3600 L/hour with an accessible limit of 100°C working temperature. You can use a battery, solar panel, or even direct current electricity as the power source.
Our DC50B series has an inlet and outlet 20mm diameter and can do a maximum working temperature of 60°C for T-series while it can work up to 100°C for S and A-series. The device weighs 600g and has speed control selections of an analog, potentiometer, or PWM in A-series.
Our DC50C model has a weight of about 600g with a max static head ranging from 6 meters to 8 meters. The max flow of this series achieves 2100 L/hour up to 2400 L/hour. Its inlet and outlet outer diameter are both ? inch thread, accessible up to 100°C liquid temperature requirements.
Conclusion
To sum it up, it is essential to know and research the main specifications that you use in a DC water pump to avoid wasting money, time, and effort. If you wish to know more about BLDC Pump products, you may check our website, https://www.bldcpump.com/.
Business Owner at Digitech Aquariums
4 年Nice