What is the function and principle of relay protection?(2)

03 Relay protection Basic tasks

① Automatically, quickly and selectively remove faulty components from the power system to prevent faulty components from further damage and ensure that other non-faulty parts can quickly resume normal operation.

②Reflect the abnormal operating status of electrical components, and act on the signal according to the conditions of operation and maintenance (such as whether there are regular personnel on duty), so that the personnel on duty can handle it in time, or the device can automatically adjust it, or change those that will cause problems if they continue to operate. Electrical equipment that is damaged or develops into an accident shall be removed. At this time, the protection is generally not required to act quickly, but a certain delay is specified based on the degree of harm to the power system and its components to avoid unnecessary movements and interference caused by temporary operating fluctuations and misoperations.

③The relay protection device can also cooperate with other automation devices in the power system. When conditions permit, predetermined measures can be taken to shorten the time of accidental power outage and restore power supply as soon as possible, thereby improving the reliability of power system operation.

04 Classification

Relay protection can be classified in the following 4 ways:

①Classification by protected objects

There are transmission line protection and main equipment protection (such as generator, transformer, busbar, reactor, capacitor, etc. protection).

②Classification by protection function

There is short circuit fault protection and abnormal operation protection. The former can be divided into main protection, backup protection and auxiliary protection; the latter can be divided into overload protection, loss of excitation protection, out-of-step protection, low-frequency protection, non-full-phase operation protection, etc.

③ Classification of signals compared and processed by protection devices

There are analog protection and digital protection. All electromechanical, rectifier, transistor and integrated circuit (operational amplifier) protection devices, which directly reflect the continuous analog quantity of the input signal, are analog protection; they use microprocessors and Microcomputer protection devices, they respond to discrete digital quantities after sampling and analog/digital conversion of analog quantities. This is digital protection.

④Classification according to protection action principle

There are overcurrent protection, low voltage protection, overvoltage protection, power direction protection, distance protection, differential protection, longitudinal protection, gas protection, etc.

05 Abnormal

When abnormalities or defects are found in the operation of relay protection, in addition to strengthening monitoring, remove the outlet pressure plate of the protection that can cause malfunction, and then contact relay protection personnel for handling.

If there are any of the following abnormal situations, you should exit in time:

①Mother differential protection

When the "bus differential AC disconnection" or "bus differential DC voltage disappears" signals are sent; when the bus differential unbalanced current is not zero; the bus tie switch without a dedicated bypass bus is in series line operation and recovery switching operation.

②High frequency protection

When the DC power supply disappears; when the regular channel test parameters do not meet the requirements; when the device malfunctions or the channel abnormal signal is sent and cannot be reset; when the parent line switch operation is in progress.

③Distance protection

When the PT used is out of operation or the three-phase voltage circuit is disconnected; under normal circumstances, the magnetizing current is too large or too small; when the load current exceeds the corresponding section of the protection allowable current.

④Microcomputer protection

When the main alarm light is on and one of the four protection (high frequency, distance, zero sequence, comprehensive weight) alarm lights is on, exit the corresponding protection; if two CPUs fail, all protections of the device should be exited; all signal lights of the alarm plug-in do not light up. If the power indicator light goes out, it means that the DC has disappeared. You should exit the outlet pressure plate and put it back in after restoring the DC power supply; the main alarm light and the calling light are on, and the CPU×ERR signal is printed and displayed. If the CPU is normal, it means that the communication loop between the protection and interface CPU is protected. Abnormal, exit the CPU inspection switch processing. If the signal cannot be reset, it means that the CPU has a fatal flaw. You should exit the protection outlet pressure plate and disconnect the inspection switch processing.

⑤Gas protection

When refueling, filtering oil or changing silica gel while the transformer is in operation; when putting the submersible pump or oil cooler (radiator) into operation after draining the oil for maintenance; when it is necessary to open the vent door or oil drain plug of the breathing system, or when cleaning the moisture absorber; when there is a load When someone is working on the oil circuit of the pressure regulating switch.

06 Analysis of common faults in relay protection

①Current mutual inductance saturation fault

The saturation of the current transformer has a great impact on the relay protection of the power system. As the terminal load of power distribution system equipment continues to increase, if a short circuit occurs, the short circuit current will be very large. If a short circuit occurs in the system close to the terminal equipment area, the current may reach or be close to more than 100 times the single rated current of the current transformer. Under normal short circuit conditions, the larger the current transformer error is, the greater the primary short-circuit current multiple increases. When the current quick-break protection reduces the sensitivity, it may prevent the operation. When a line is short-circuited, the current of the current transformer is saturated and the secondary current induced again is small or close to zero, which will also cause the definite time overcurrent protection device to be unable to operate. When the overcurrent protection of the outlet line of the power distribution system refuses to operate, causing the inlet line protection of the power distribution station to operate, the entire power distribution system will experience a power outage.

②Improper selection of switch protection equipment

The selection of switch protection equipment is a very important task. Most of the current power distribution systems have established switching stations in areas with high load density, that is, using the power supply and transmission model of substation-switching station-distribution transformer. In switch stations where relay protection automation is not implemented, we should use more load switches or relay equipment systems combined with them as switch protection equipment.?

07 Handling methods and measures for relay protection faults

① How to deal with common relay protection faults

a. Substitution method

Replacing the faulty component with a good component to judge whether it is good or bad can quickly narrow down the fault search scope;

b.Reference method

By comparing the relevant technical parameters of normal equipment and abnormal equipment, we can find out the fault points of abnormal equipment. This method is mainly used to check for wiring errors and faults where the test value is significantly different from the expected value during the fixed value verification process. When the secondary wiring cannot be restored correctly after modification or equipment replacement, refer to the wiring of similar equipment. And during the relay setting value verification, if it is found that the test value of a certain relay is far different from the setting value, at this time, you cannot easily make a judgment and judge that the characteristics of the relay are not good, and you should adjust the scale value on the relay. You can use the same meter to measure other similar relays in the same circuit for comparison;

c. Short circuit method

Short-circuit a section or part of the circuit with a short wire to determine whether the fault exists within the range of the short wire or elsewhere to determine the scope of the fault. This method is mainly used when the electromagnetic lock fails, the current loop is open, the switching relay does not operate, and it is used to determine whether the contacts of the control switch are intact.

② Measures to ensure normal operation of relay protection

Reasonable staffing ensures that personnel scheduling and assistance can be carried out smoothly, clear personnel work goals, and ensure the normal operation of power; improve rules and regulations, and improve and improve the rules and regulations for the operation and management of protection devices and relay protection equipment based on the characteristics of relay protection. Accounts, operation and maintenance, accident analysis, regular calibration, defect handling and other files should gradually adopt computer management tracking inspection, strict assessment, and implementation of rewards and punishments; the status monitoring method should be implemented for secondary equipment. For comprehensive automated substations, it is easy to implement continuous Electrical protection status monitoring.

Thanks for reading and if helps,Please follow and forward.