What is an Annular Ring?

What is an Annular Ring?

Annular rings are a vital part of any printed circuit board (PCB), but they pose quite a challenge for PCB designers. With such precise work, it’s easy to make mistakes with drilling the via, which can lead to malfunctioning on the board itself.?

PCB designers have to be careful when calculating size and placement. In this article, we’ll explore everything you need to know about annular rings, the unique challenges they present, and how to get them right.

WHAT IS AN ANNULAR RING?

The annular ring is nothing but a technical term that is designated to the area drilled into the PCB. The hole that is created by the process serves as an interconnecting node between?different layers of the circuit.

No alt text provided for this image

But before you know the basics of annular ring creation, it is important to know how the via is made. It usually starts during the PCB manufacturing process. To fulfill the general requirements, PCB boards are etched with a hole in which copper is deposited through electroplating.

After the PCB construction is finished, these hole-like structures that act as a connection between PCB pads appear as rings when viewed from above. Another specialty of annular rings is that they differ in size. Depending on the requirement, they can either be thick or thin.

HOW DO YOU CALCULATE THE ANNULAR SIZE?

When constructing an annular ring, the goal is to drill right through the center. The more accurate that hole is, the more seamlessly electricity conducts through.?

To get the correct width for an annular ring, use a simple equation:

  • Width of Annular Ring = (Copper Pad Diameter – Diameter of Finished Hole/Via) / 2

So you take the diameter of the copper pad, which is the outer circle, and subtract the diameter of the via, which is the inner circle. Take that number and divide it in half to get the perfect width of your annular ring.

WHY DOES THE ANNULAR RING SIZE MATTER?

The size of the annular ring matters because it determines the success of your conductivity. While you don’t want it to be too wide since you’re working with a tiny space, you do need it to be wide enough to keep the connection strong.?

HOW TO GET THE ANNULAR RING SIZE RIGHT

Each PCB manufacturer will stipulate the tolerance for the annular ring through the?PCB manufacturing process. However, to be on the safe side, you should always add a little more space.?

Most designers recommend increasing the size by 1.0mm from the manufacturer’s specifications. The slight extra width will help prevent any issues later on.?

The size of your annular rings will also depend on what you’re designing the board for. The Institute of Printed Circuit Boards specifies three categories for PCBs: Class 1, Class 2, and Class 3. Heavy-duty PCBs need larger annular rings because the via will be wider in diameter. Class 3 PCBs require more heavy-duty annular rings.

WHAT IS THE MINIMUM ANNULAR RING IN PCB?

While some PCBs support heavy-duty equipment and spaces, others must be extremely compact. Think of PCBs in smartphones or small technological equipment.?

In this case, the minimum annular ring has to be correspondingly tiny. But just how small can we go?

The design standard across the industry sets a different limit for inner and outer annular rings.?

  • For annular rings on the inner layer of a PCB, the minimum width is 0.1mm.
  • For annular rings on the outer layer of a PCB, the minimum width is 0.05mm.

You can learn more about?design limits?on Candor.?

WHAT IS THE DIFFERENCE BETWEEN A PCB ANNULAR RING AND A THROUGH-HOLE?

Whenever you hear the term PCB, you probably think of the through-hole method. It is a technique used to mount electronic components. The electronic components insert into holes drilled in a PCB.

Through-holes are a type of via, but not all vias are through-holes. Through-holes use leads inserted into the hole and then soldered onto the copper pad to create conductivity.

On the other hand, Annular rings create conductivity by directly connecting the copper-plated via to the copper pad.

WHAT IS THE TEARDROP ANNULAR RING?

A teardrop annular ring is teardrop-shaped. Instead of designing a perfect circle, you add extra copper to connect the ring’s outer edges. The additional copper gives the ring some added strength.

The main reason to use teardrop annular rings is if the drill bit goes slightly off course during drilling. This problem can remove too much copper and jeopardize the connection.?

Teardrop annular rings can:

  • Reduce the risk of cracking on thin copper
  • Reduce mechanical or thermal stress
  • Protect small misalignments in the drill hole

要查看或添加评论,请登录

Lily Zhang的更多文章

  • The Basics Of Soldering Explained

    The Basics Of Soldering Explained

    Soldering electronics is a delicate art. If you’re just getting started learning how to solder, this handy reference…

  • What is force sensor?

    What is force sensor?

    Force sensors are used to either detect the pressure or weight of an object which can be detected by any…

  • Design Suggestions of Rigid-flex PCB

    Design Suggestions of Rigid-flex PCB

    COMMON STRUCTURES OF RIGID-FLEX PCB The rigid flex board is to glue one or more rigid layers on the flexible board. The…

  • 10 PCB Design Tips

    10 PCB Design Tips

    All of us want to design PCB prototypes as cheap as possible and as fast as possible, without many trials and errors…

  • What is BGA Chip ?

    What is BGA Chip ?

    BGA (Ball Grid Array) is a technology for surface mounting ICs using small balls on the underside of the chip package…

  • How are multilayer circuit boards made?

    How are multilayer circuit boards made?

    How are multilayer circuit boards made? Step 1: Inner layer core selection PCB core material The stack-up designates…

  • How RF Microwave PCBs are different from ordinary PCBs

    How RF Microwave PCBs are different from ordinary PCBs

    All high-frequency PCB operating beyond 100 MHz are termed as RF PCBs whereas a Microwave RF PCB operates above 2GHz…

  • Tenting vias, plugged vias and via in pad

    Tenting vias, plugged vias and via in pad

    Tenting vias It’s the most popular and mature process in PCB fabrication, and tenting vias mean to cover the annular…

  • How to design a board with controlled impedance?

    How to design a board with controlled impedance?

    WHAT IS A CONTROLLED IMPEDANCE? Controlled impedance is the characteristic impedance of a transmission line formed by…

  • RF PCB Design

    RF PCB Design

    An RF PCB design is a bit different from a conventional board. What makes it distinct are parameters like impedance…

    1 条评论

社区洞察

其他会员也浏览了