Pulse Amplifier Definitions and Terminology
Pulse amplifiers are amplifiers designed specifically to amplify signal pulses. Pulse signals are non-continuous, time-varying signals that are characterized by a short duration and high frequency. Pulse amplifiers have a unique set of parameters that are used to define the pulse signal and their properties. This article defines the key terms associated with Pulse Amplifiers.
Pulse Amplifier Specifications
Duty Cycle:?The typical maximum duty cycle specification for used in EMC applications is 6%. The desired PRF rate is set up externally on the test equipment but can be viewed on the ACURAMW front panel display. This feature is useful for ease of setup with respect to customer applications. The ACURAMW Amplifiers indicate the Duty Cycle/Pulse Rep Rate and the Pulse Width. Most ACURAMW Solid-State Pulse Amplifiers can operate up to or @ 10% Duty Cycle, 20% for some models.
Pulse Rate:?The Pulse Repetition Rate (or PRF) known as the “PRF specification” is typically 100 kHz maximum for EMC applications. Some other applications require higher PRF rates as dictated by the requirement. The PRF rate is the pulse train applied as a TTL level that is applied to the pulse input connector for modulating/switching the RF on and off at the rate applied. Most Solid-State Pulse Amplifiers can operate to a PRF rate of 400 kHz.
Rise / Fall Time:?The Rise/Fall time is the time defined for the leading or trailing edge of a pulse measured from the 10% to 90% points of the pulse. Most standard ACURAMW Solid-State Pulse Amplifiers provide Rise/Fall times in the 15-25 nsec range.
Pulse Width:?The maximum pulse width specification can be based on the specific Solid-State technology incorporated within the amplifier and its capability. Typically, most ACURAMW Pulse Amplifiers for instrumentation/EMC testing applications are specified at 100 usec for a maximum pulse width. However, some requirements can be for wider pulse widths if the technology can support the specific application.
Pulse On/Off Ratio:?The RF Pulse On/Off ratio is typically specified at 80 dB. This is because when the Solid-State High-Speed Switching circuits are engaged the RF is no longer enabled to be amplified and transmitted through the RF-line.
RF Delay:?The RF Pulse delay is the difference in time from when the TTL Pulse trigger is applied to the Pulse input connector to when the RF pulse is present. This is the time for the propagation through the system to enable the RF Amplification through the RF lineup.
Pulse to Pulse Jitter:?The deviation/variation from the leading edge of each repeating pulse.
Pulse Width Jitter:?The deviation/variation in the Pulse Width for each repeating Pulse.
Pulse to Pulse Stability:?The amplitude deviation/variation from Pulse to Pulse.
Duty Cycle Correction Factor:?Knowing the Duty Factor or Duty Cycle allows simple multiplication or division to arrive at a peak power level given an average level or vice versa. For example, a pulse signal with?a duty cycle of 10% and an average power indication of 100 watts would be multiplied by?10 to arrive at a 1KW peak power. The same 10% duty pulse train is 1/10th or the total?time period so the average power level would be 10 times less than the peak or -10 dB.?The same process would hold true for a 1% duty cycle signal, but the average power would?be multiplied or divided by a factor of 100 or 20 dB.
Forward and Reflected Peak Power:?ACURAMW Solid-State Pulse Amplifiers with the Option DMC, include a power indication function that shows both forward and reflected peak power on the front panel display. Additionally, they include a real-time VSWR measurement within each customer’s specific application. Not all labs are outfitted with peak power analyzers so power verification can be done in an average mode converting average power to peak power with the standard formula.
Duty Cycle Correction + Average Power = Peak Power
Example:
领英推荐
Solid-State Amplifier Operation Description Turn ON/OFF
Pulse Amplifiers amplify RF signals applied to the RF input. Amplifiers have a Pulse input connection that accepts a TTL pulse level from an external pulse generator or signal source for modulation of the RF-Line. The RF is modulated from the pulse input connector via internal switching circuitry. This method of pulse modulation enables very fast Rise/Fall times for almost all customer applications. The fast switching provides the >80 dB ON/OFF ratio with typically 15-20nsec Rise/Fall times for ACURAMW Pulse amps. RF pulse bursts can be applied to the RF input while the pulse input has the RF line Enabled. Various combinations can be applied to fulfill whatever your test requirements specify. Although six percent (6%) is a typical duty cycle for most EMC applications, higher duty cycles are often available. Pulse amplifiers are used for Radar and Satellite and EMC applications.
Illustration 1 above shows the Pulse response for a High-Power Solid-State Amplifier. The Pulse overshoot can be seen to be less than a Pulse TWT, which is typically < 0.1dB. THe Rise Time as is typically equal or better than a Pulse TWT and the Fall Time is typically equal or better than a Pulse TWT.
Illustration 2 above shows the Pulse response for a High-Power Pulse TWT Amplifier. The Pulse overshoot is typically 1dB. Rise Time and Fall Time are not significantly different from the SSPA.
This article has been contributed by Acura Microwave Tech. The company designs and manufacturers Solid-State Pulse Amplifiers for a wide range of applications.
The ACURAMW"s Pulse Series Amplifiers( From 10MHz-40GHz and Power UP TO 20KW)
Key features of ACURAMW Pulse Amplifiers
Protection
High Stability For:
Additional Standard Features with ACURAMW Option DMC
Large Front Panel Color-Touchscreen Display
The ACURAMW SSPA monitors and transfers the operating voltages and currents to the Large Color Touchscreen Display. This aids the user in troubleshooting in the event of a failure. The amplifier indicates on the display where the fault has occurred.