Project of the Week of 07/04/22

Project of the Week of 07/04/22

Project of the week is a Plastic Wear Plate that supports heavy loads and must be non-abrasive to its mating surfaces. This was originally made from Cast Iron with bonded UHMW-PE, and a bronze version was also used in past versions. This part is roughly 12-1/2" x 11-1/4" x 1-3/4" and is used in an outdoor industrial environment. We cannot mention what the bores are used for and for what application this is replacing. We are tasked with producing 25 pcs in Nylatron GSM Blue Nylon; customer will be conducting the destructive testing and comparing performance over its prior materials.

No alt text provided for this image

End Mills and Chamfer Mills will be solid carbide from Harvey Tool with standard High-Speed Drills and taps for the small bores. Large bores are done with a Criterion boring head with a carbide tipped boring bar. No special fixturing is required to hold this, but pressure from the vise must be light and verified from distorting the large bores. Part tolerance except the large bores is?+/- 0.020 and a machine finish with chamfer edges is fine for this part. The large bores require an O-ring which require a finish to 63 Ra or better since it will be a liquid seal with a +/- 0.003 tolerance. These areas must be checked for deep scratches before and after machining. Nice project to start this week of 07/04/22. We would like again to thank our customers for allowing us to share our projects with people who value the manufacturing talent that is out there... If you have similar projects like this and would like to receive a quote from us, please reach out to us for further information.

要查看或添加评论,请登录

Pedro Henriques的更多文章

  • Project of the Week of 02/16/09

    Project of the Week of 02/16/09

    Project of the week is a Transformer Bobbins that is injection molded from Natural Rynite FR-530 Polyester resin. This…

  • Project of the Week of 04/20/09

    Project of the Week of 04/20/09

    Project of the week is an Upper Motor Housing Cover injection molded from Rynite FR-543 Polyester resin. According to…

  • Project of the Week of 11/13/06

    Project of the Week of 11/13/06

    Project of the week is an injected molded Tag Holder made of Red Cycolac ABS. These parts are roughly 8" x 5" x 1/2"…

  • Project of the Week of 05/20/14

    Project of the Week of 05/20/14

    Project of the week is a 10 Station Filter Docking Check Valve Distribution Manifold made of Acetal. This part is…

    1 条评论
  • Project of the Week of 05/12/14

    Project of the Week of 05/12/14

    Project of the week is a 10 Station Filter Docking Press Station made of Acetal. This part is roughly 26" x 13" x…

  • Project the Week of 10/13/14

    Project the Week of 10/13/14

    Project of the week are 4 different SAE Port Flanges typically made of aluminum and steel, these however are low…

  • Project of the Week of 04/07/07

    Project of the Week of 04/07/07

    Project of the week is a Door Latch Sensor Housing machined from High Impact Polystyrene. This part was eventually…

  • Project of the Week of 06/05/07

    Project of the Week of 06/05/07

    Project of the week is a Dual Balance Wheel Housing made of Black ABS. This part was eventually injection molded once…

  • Project of the Week of 09/04/06

    Project of the Week of 09/04/06

    Project of the week is a Medical Clip Stake Holder made of Blue SUSTAPEEK MG. This part will eventually be injection…

  • Pject of the Week of 06/23/13

    Pject of the Week of 06/23/13

    Project of the week is a 7075-aluminum adapter plate we designed and machined for a client to convert an original…

社区洞察

其他会员也浏览了