Fully automatic linear olive oil filling metal caps capping labeling machine

The 4heads olive filling machine, controlled by the microcomputer, combines the photoelectricity with the pneumatic operation, thus widely is applied for the liquid filling of?the agriculture chemical, solution, liquid detergent, cosmetic as well as olive. The filling volume is precise, foamless, and stable.

The machine can fill the liquid with the range from 25-1000ml, meanwhile, there is no special requirement on the shapes of bottles. That is to say, it can fill the liquid for the normal bottles as well as the irregular-shaped bottles.

Parameter of Model YX-5030:

Model?YX-5030

Filling range?50～3000ml

Filling speed?＜20-30b/m（for 500-1000ml liquid）

Accuracy ±1%

Power/supply power?0.8kw、220v

Working pressure?5～6kg/cm3

Air consumption?0.5-0.7mpa

N.W 500kg

Outer dimension?2000×800×1900mm

Mark: The filling nozzles can be designed and manufactured according to requirements?from customers on the filling range and filling speed.

Filling speed adjustment

Filling speed adjustment has the following 6 factors:

1, the speed of the product is determined by the viscosity of the product and the length of the suction pipe.

2, filling speed depends on the diameter of the filling head, the diameter is large, the speed is quick.

3, the product of the bubble level. The product filling speed of the high bubble should be slowed down.

4, how much is the filling quantity.

5, the accuracy of the filling quantity, adjust the filling time of each cast.

6, adjust the filling speed (that is, the speed of the servo motor).

General trouble shooting and processing:

1）Touch screen is not shown, but the indicator light

Fault cause:

Check whether the fuse is burning, or the contact is bad, replace or reinstall the fuse.

2）The output indicator of the programmable controller has an output indicator, but the solenoid valve does not work.

Fault cause:

Upon examination of the solenoid valve failure, is the key to the programmable controller in the electrical damage, can replace the same type of intermediate relay, fault can be ruled out (this fault is very rare).

3）The main head there is a leak in the shutdown.

Fault cause:

The filling head cylinder does not move up and down, replaced PTFE head, check on the stingy joints have gas, or replace the filling valve, can be ruled out

4）After filling in a number of bottles do not fill

?Fault cause:

?Check whether the bottle counting electric eye, if not counting adjustable electric distance so that it can reach the count;

? Check that the liquid level indicator is black, if it is white, and the liquid level is fluid and can be filled with black

? Check the magnetic switch cylinder after the dive, the light is bright, if not bright, adjust to the light.

?Check the back of the servo motor is close to the switch is bright, if not bright, adjust to the light.

5)Individual valve or cylinder action to slow down or do not work.

Fault cause:

?The general situation is caused by the fault of the control valve, first check to control the output of the display lamp (in the lower left of the programmable controller) work is normal, confirm the normal operation of the following check.

?Magnet coil plug for transposition of the solenoid valve, if change the position of the fault, indicating that the electromagnet coil is damaged, replace the coil after failure can be ruled out.

If the valve group of the emptying port does not stop to have a lot of gas, the system has a more serious leakage. Can check the internal sealing condition, if damaged, should be replaced. If the fault can not be ruled out, can check the valve spool movement, see if there is a card phenomenon or the seal is damaged, and repair, if damaged more serious, it should be replaced by the entire valve.

6）Servo motor alarm.

Fault cause:

?Check whether the PLC on the F**, if it is to turn off the power, and then open up to the manual operation, a number of seconds after the manual injection, and then press the manual back to zero.

Nitrogen gas flushing system

YX-AC40 Automatic ROPP capping machine for the olive bottle with metal caps with protective chamber

Automatic ROPP capping machine with button controlling system

Capping heads for ROPP capper

The capping machine is suitable equipment for roll-press-sealing the Aluminum caps for the plastic bottle、pet bottle、as well as glass bottle. It precesses the screw-press capping for the bottle under the rolling press from hobs, automatically feeding bottle、caps, removing the reverse caps. The capped bottle favors the characteristics like the stable capping effect, convenient uncapping so that it functions as counterfeit and anti-theft

Product parameter of Model YX-AC40

Model YX-AC40

Supply powder (V/Hz)???AC 220/50?380/60

Capacity (m/min)??≧4000B/M

Cap size (mm) 250-1000

Application??????Alum-caps

Air exhaust from Vacuum pump (m3/h)?5KG

Outer dimension（L×W×H）(mm)??????2000×1000×2300

N.G (kg) 520

Drawing of ROPP capping working process(taking example as an automatic line with conveyor platform)

How to operate model YX-C25 Single head ROPP capping machine

The feed container moving on the conveyor belt is feed into an in-feed star wheel through In-feed worm, star wheel bringing the container below the sealing head in the subsequent indexing part, meanwhile, the bottle picks up a cap from the delivery chute of the cap filling bowl, where the body and the neck of the container are positioned below the rotating head, where the sealing head is performing the perfect operation of threading & sealing.

Salient Features : The unit is made compact & versatile. S.S. Slat conveyor S.S. Elegantly Matt Finished Body Built-in front control panel Vibratory Bowl With A/c Frequency Drive

Model YX-650A double-sided labeling machine

The labeling equipment is for the round bottle labeling in the industry like food, oil, pharma, wine, cosmetics, and so on.

The machine with elegant design can be easily operated and maintained by the common worker, who requires no special training in operating this machine.Just give a simple adjustment to produce another product when you want to swap the different kinds of bottle labeling.

Metal caps capping+labeling line

The bottle labeler is thus out from as below-mentioned characteristics:

1:The main body of equipment is made of SUS304 and advanced Aluminum products.

2:The labeling heads are driven by the stepping motor that is imported from Japan.

3:All the light sensor equipment is imported from both Japan and Germany

?4:PLC Controlled by the human-machine interface with 60 memory units

5:The machine is the best choice for single worker’s operating.

6:The machine has the function of bottle-uprighting,bottle-distributing、labeling、flating as well as counting.

7:The position、height、angle of labeling can be adjusted easily.

8:Equipped with the conveyor belt, the machine is applied to a set off the production line.

Basic parameter of double sides labeling machine

turntable for accumulation of final product

Packing before shipment

The packing machines are mainly designed and manufactured according to specific requirements.