Cimarron的动态

This is FIRE! ?? ?? But is it good enough? ??♂? Is your Flare in compliance? OOOOb/c that's a lot of letters but some look at them like a four letter word. Cimarron can help! ?? Reach out in the comments or DM. ? We can discuss how to get your flares in compliance.

With new EPA regulations in place, don’t wait to update your flare—Cimarron has the experience to help you stay compliant and efficient!

With new EPA regulations in place, don’t wait to update your flare—Cimarron has the experience to help you stay compliant and efficient!

Bring your aging machine into the 21st century with the Steam Turbine Seal (STS?). The STS? mechanical seal has been developed in conjunction with a major oil refinery to replace existing carbon ring seals normally fitted to steam turbines. STS? adopts AESSEAL? dry running gas compressor seal technology to provide a solution that significantly reduces the steam leakage typically associated with standard carbon ring seals. Typical Benefits of Steam Turbine Mechanical Seal Technology: ? Increased turbine reliability ? Reduced turbine maintenance costs ? Reduced bearing contamination ? Non-contacting technology extends life of seal ? Elimination of Shaft Wear – generated by the Carbon seal ? Greatly reduces steam loss and increases efficiency ?? https://hubs.ly/Q02QyQJG0 ?? [email protected] ?? +91 2113 233 333 #AESSEAL #mechanicalseals #pumptechnology #engineeringsolutions #steamturbine #steamturbineseal #STS

?? Coupling Alignment Fundamentals?? ?? 22-Nov-2024 | SN.: 050 #CouplingAlignment #RotatingEquipment #MachineryReliability #Maintenance #ConditionMonitoring #MechanicalEngineering #OilAndGas #EnergyIndustry #PredictiveMaintenance #EngineeringSolutions

How can the introduction of a safer, more efficient Permanent Magnet Motor transform your operations? ?? Learn more in this great article from World Oil: https://lnkd.in/d9S4zYMt #BakerHughes #WorldOil #WeAreBakerHughes #OilAndGas #Innovation #Efficiency

OTA is proud to offer gas-assisted flares for situations where additional flare tip agitation is needed but air blowers aren’t available. This innovative solution is particularly beneficial when faced with low waste gas pressure, high BTU gas, or gas constituents that tend to produce smoke. By introducing turbulence at the flare tip, our gas assist technology enhances oxygen mixing, promoting efficient, smokeless combustion. This is a game-changer for maintaining optimal flare performance in challenging conditions! In addition to our gas-assisted flares, we also offer air-assisted, utility, and dual flares! Let us know how how we can help promote smokeless operations! #Flares #Emissions #EnvironmentalCompliance #OOOO #OilandGas https://lnkd.in/gUAy8zfb

Installing a gas cylinder at each of your workstations is a dangerous idea. One leak in a gas storage container or delivery subsystem could cause equipment damage to your entire production line. Gas panel safety is key to protecting your production space. Instead, consider?gas panel safety features?as a solution. They provide a centralized location for gas cylinders and regulators, with pipelines that flow gasses to output locations throughout your subsystems. In addition, implementation of these systems allows for gas cylinder switch-outs to happen more conveniently, with less disruption to the production floor. This also reduces the number of canisters taking up space on the floor. Learn more: https://lnkd.in/gBFD5JKq

Inspection of 1st stage Nozzle of Gas Turbine is a critical maintenance procedure and covered during Hot Gas Path Inspection (HGPI) or Major Inspection (MI).Serving as the gateway between the combustion chamber and the turbine section, it directs and accelerates the flow of hot gases produced by combustion towards the turbine blades. Following are the important checks to be performed during inspection: 1.??????NDT Techniques (i.e. DPT or FMPI) ?for Crack Detection. a.??????Dimensions & Locations of cracked to be inspected as per OEM criteria. b.?????Crack at leading edge of Segment is not acceptable. 2.??????Dimensional Checks for Ovality 3.??????Ensure proper opening of Cooling or Dilution holes thru Air & Soap arrangement (Explained in below video) 4.??????Inspection of Sealing Strips 5.??????Inspect Airfoil of nozzle segment for any wear sign #1ststageNozzle #HGPI #MajorInspection #Overhauling #gasturbine #overhauling #TBCCoating #coolingholes #FuelGas #fertilizer #turbomachinery #powergeneration #Utilities #OilandGas #maintenance #GasTurbine #Turbomachinery #Maintenance #Utilities #PowerGeneration #GE10/1 #PakarabFertilizer #FatimaFertilizer #FatimaGroup #MaintenanceTurboMachinery

New Blog Post Alert! At Turbine Solutions PTY Ltd, we understand the importance of maintaining the efficiency and reliability of gas turbines. Our latest blog post dives into the Top 5 Common Issues in Turbine Maintenance and How to Solve Them. ?? Blade Erosion and Corrosion ?? Seal Leakage ?? Bearing Failures ?? Combustion Instability ?? Thermal Fatigue